...

🍪 This website requires cookies to provide all of it's features. Please enable your browser cookies.

Accept All Decline All
REQUEST A QUOTE

Triple Offset Butterfly Valve

Our valves utilize cutting-edge technology, undergo rigorous quality control, ensuring outstanding performance and durability.

  1. Home
  2. »
  3. Product
  4. »
  5. Triple Offset Butterfly Valve

Triple Offset Butterfly Valve

Triple-offset butterfly valves feature a conical sealing geometry that allows the disc to disengage completely from the seat around its entire circumference as soon as it begins to open. This eliminates rubbing contact throughout the opening and closing strokes. During closure, the disc is wedged against the seat along the conical sealing surfaces, providing metal-to-metal sealing.

Face-to-face dimensions comply with ANSI B16.10, flange dimensions with ANSI B16.5, design and manufacture are in accordance with API 609, and pressure testing is performed in accordance with API 598. The product range covers NPS 2–24 and Class 150–300. Available body materials include WCB, CF8M, and other grades. The sealing surfaces can be hardfaced with Stellite.

Product Description

The Triple-Offset Design Principle

The defining feature of a triple-offset butterfly valve is that the sealing surfaces make contact only at the moment of closure.

First offset: The sealing surface is offset from the stem rotation axis.

Second offset: The stem axis is offset from the pipeline centerline.

Third offset: The conical seat geometry is angled relative to the pipeline axis.

The combined effect of these three offsets allows the disc to disengage completely from the seat along the conical sealing geometry as soon as it begins to rotate. No sliding friction occurs between the sealing surfaces throughout the operating stroke. As the valve closes, the disc wedges into the seat along the cone, increasing the sealing force as closure is completed.

Metal Sealing: Advantages and Trade-Offs

Because triple-offset butterfly valves use metal-to-metal sealing, the sealing surfaces are often hardfaced with Stellite or other hard alloys to provide wear resistance, high-temperature capability, and long service life. This makes them suitable for high-temperature, high-pressure, and particulate-laden applications.

However, metal sealing relies on wedge action rather than the elasticity of rubber. Operating torque is therefore significantly higher than that of a concentric butterfly valve, and large-diameter valves may require a gearbox or actuator. Sealing performance also depends heavily on machining and assembly accuracy; even minor deviations in the conical mating surfaces can compromise shutoff performance. In general, the achievable leakage performance of metal-to-metal sealing is less tight than that of soft-seated rubber valves.

Positioning Within the Butterfly Valve Range

Triple-offset butterfly valves occupy the higher-performance end of the butterfly valve range:

Concentric soft-seated butterfly valves: Suitable for clean media at ambient temperatures where economy is a priority.

Double-offset butterfly valves: Suitable for general service requiring durability and reliable operation.

Triple-offset butterfly valves: Preferred for high-temperature, particulate-laden, or demanding applications requiring long service life and friction-free operation.

The sealing material, cone angle, and actuator torque must be selected together to ensure reliable performance. Each valve is designed in accordance with API 609 and tested in accordance with API 598.

Applications

High-temperature steam and hot oil pipelines: Metal sealing provides high-temperature capability, friction-free operation, and long service life.

Pipelines carrying particulate-laden or scale-forming media: The non-rubbing sealing design reduces the risk of scratches caused by solid particles.

Large-diameter pipelines requiring long service life and minimal maintenance: Hardfaced sealing surfaces provide improved wear resistance.

Frequently operated pipelines: Friction-free movement throughout the operating stroke minimizes sealing surface wear.

High-parameter process pipelines: Select body and sealing surface materials according to the pressure rating, operating temperature, and process medium.

4. Selection Guidelines

Choosing Between Concentric, Double-Offset, and Triple-Offset Designs: Select a concentric soft-seated valve for clean media at ambient temperatures, a double-offset valve for general service, and a triple-offset valve for high-temperature, particulate-laden, or long-life applications.

Sealing Surface Materials: For high-temperature service or significant erosion, consider Stellite or other hard alloys applied by hardfacing. Select the sealing surface hardness and mating material combination according to the process medium and operating conditions.

Operating Torque: Metal-seated valves require higher torque. For large diameters or high differential pressures, provide a gearbox or actuator and calculate the required torque at the maximum differential pressure.

Installation Orientation: Install the valve according to the flow direction markings on the body to minimize uneven loading during closure.

Expected Leakage Performance: Metal-to-metal sealing may permit a small amount of leakage. The required leakage acceptance criteria must be agreed upon at the time of ordering in accordance with the applicable standard; soft-seat bubble-tight requirements should not be assumed.

5. Project Case Study

Customer: Honeywell UOP LLC, MalaysiaApplication: High-Temperature Process Pipelines in Refinery Hydrocracking and Reforming Units

The project involved DN 600, Class 300 high-temperature process pipelines operating at 400°C. The original soft-seated butterfly valves suffered from seat aging and failure at elevated temperatures, resulting in internal leakage and repeated plant load reductions.

Flowork supplied 42 DN 200–900, Class 300 triple-offset metal-seated butterfly valves featuring A216 WCB valve bodies, CF8M stainless steel discs, hardened 17-4 PH stems, Stellite 6 hardfaced metal sealing surfaces, a triple-offset design providing friction-free opening and closing, and flanged connections.

The valves were designed in accordance with API 609 Category B and underwent shell and seat leakage testing in accordance with API 598, witnessed by the UOP Quality Control Department.

Since commissioning in May 2022, the valves have operated continuously for 3 years with zero internal leakage. Plant load reductions decreased from 5 times per year to zero, and annual steam consumption decreased by approximately 6%.

6. Frequently Asked Questions (FAQs)

Q1: Why does a metal-seated butterfly valve require significantly higher operating torque than a rubber-seated valve?

Metal sealing relies on a wedging action along the conical sealing surfaces, requiring greater closing torque. Actuator sizing must be based on the required torque at the maximum differential pressure, not on the no-load torque.

Q2: Can metal-to-metal sealing achieve zero leakage?

Achieving absolute zero leakage with metal-to-metal sealing is difficult. A small amount of leakage may be permitted, depending on the design and test requirements. The acceptable leakage rate must be agreed upon at the time of ordering in accordance with the applicable standard; bubble-tight requirements for soft-seated valves should not be assumed.

Q3: What should I do if the valve becomes harder to operate at high temperatures?

Thermal expansion may change the clearances between the conical sealing surfaces. First, verify that the actual operating temperature matches the design conditions. Do not attempt to overcome the resistance by applying excessive torque. If necessary, have the manufacturer review the clearances and sealing geometry.

Q4: Can the valve remain in service if the sealing surfaces are scratched?

Minor scratches may still allow the valve to meet the agreed leakage acceptance criteria. If leakage exceeds the specified limit, the sealing surfaces should be repaired and lapped, or the sealing components should be replaced.

Class150  
Triple Offset Butterfly Valve


NPS

in

2

3

4

6

8

10

12

14

16

18

20

24

d

mm

51

76

102

152

203

254

305

337

387

438

489

591

L(RF)

mm

43

48

54

57

64

71

81

92

102

114

127

154

\L1(RF)

mm

108

114

127

140

152

165

178

190

216

222

229

267

d1

mm

92

127

157

216

270

324

381

413

470

533

584

692

d2

mm

120.5

152.5

190.5

241.5

298.5

362

432

476

540

578

635

749.5

D

mm

152

190

229

279

343

406

483

533

597

635

699

813

b

mm

16

19

24

26

29

31

32

35

37

40

43

48

n-Фd

mm

4-19

4-19

8-19

8-22

8-22

12-25

12-25

12-29

16-29

16-32

20-32

20-35

H

mm

225

255

285

332

386

427

498

510

540

585

642

693

H1

mm

112

126

146

170

218

245

290

316

352

386

415

482

W

mm

300

300

300

300

300

300

500

500

600

600

600

600

Class300  
Triple Offset Butterfly Valve

NPS

in

3

4

6

8

10

12

14

16

18

20

24

d

mm

76

102

152

203

254

305

337

387

432

483

584

L(RF)

mm

48

54

59

73

83

92

117

133

149

159

181

\L1(RF)

mm

114

127

140

152

165

178

190

216

222

229

267

d1

mm

127

157

216

270

324

381

413

470

533

584

692

d2

mm

168.5

200

270

330

387.5

451

514.5

571.5

628.5

686

813

D

mm

210

254

318

381

445

521

584

648

711

775

914

b

mm

29

32

37

42

48

51

54

58

61

64

70

n-Фd

mm

8-22

8-22

12-22

12-25

16-29

16-32

20-32

20-35

24-35

24-35

24-41

H

mm

265

290

355

418

456

498

547

582

651

704

780

H1

mm

130

150

185

236

273

313

338

392

420

465

532

W

mm

300

300

300

500

500

600

600

600

600

600

600

API Trim NO.
Table

 

No
  of internal parts

 

Seat
  ring or body

 

Gate、disc 、ball or body

 

Stem

 

No
  of internal parts

 

Seat
  ring or body

 

Gate、disc 、ball or body

 

Stem

01

13Cr

13Cr

13Cr

31

STELLITE

321SS

321SS

02

304SS

304SS

304SS

32

STELLITE

STELLITE

321SS

03

310SS

310SS

310SS

33

347SS

347SS

347SS

04

HARD 13Cr

HARD 13Cr

13Cr

34

STELLITE

347SS

347SS

05

STELLITE

STELLITE

13Cr

35

NICKEL ALLOY

13Cr

13Cr

06

Cu-Ni

13Cr

13Cr

36

A105/PTFE

A105+ENP

A105+ENP

07

13Cr

HARD 13Cr

13Cr

37

A105/PTFE

WCB+ENP

A105+ENP

08

STELLITE

13Cr

13Cr

38

13Cr/PTFE

13Cr

13Cr

09

Cu-Ni

Cu-Ni

Cu-Ni

39

304SS/PTFE

304SS

304SS

10

316SS

316SS

316SS

40

316SS/PTFE

316SS

316SS

11

Cu-Ni

STELLITE

Cu-Ni

41

A105/RPTFE

A105+ENP

A105+ENP

12

STELLITE

316SS

316SS

42

A105/RPTFE

WCB+ENP

A105+ENP

13

ALLOY 20

ALLOY 20

ALLOY 20

43

13Cr/RPTFE

13Cr

13Cr

14

STELLITE

ALLOY 20

ALLOY 20

44

304SS/RPTFE

304SS

304SS

15

STELLITE

STELLITE

304SS

45

316SS/RPTFE

316SS

316SS

16

STELLITE

STELLITE

316SS

46

A105/NYLON

A105+ENP

A105+ENP

17

STELLITE

STELLITE

347SS

47

A105/NYLON

WCB+ENP

A105+ENP

18

STELLITE

STELLITE

ALLOY 20

48

A105/NYLON

304SS

304SS

19

MONEL

MONEL

MONEL

49

A105/NYLON

316SS

316SS

20

BRONZE

BRONZE

13Cr

50

13Cr/NYLON

13Cr

13Cr

21

HASTELLOY B

HASTELLOY B

HASTELLOY B

51

304SS/NYLON

304SS

304SS

22

 

HASTELLOY C

HASTELLOY C

52

316SS/NYLON

316SS

316SS

23

STELLITE

304SS

304SS

53

A105/PEEK

A105+ENP

A105+ENP

24

304LSS

304LSS

304LSS

54

A105/PEEK

WCB+ENP

A105+ENP

25

STELLITE

304LSS

304LSS

55

13Cr/PEEK

13Cr

13Cr

26

STELLITE

STELLITE

304LSS

56

304SS/PEEK

304SS

304SS

27

316LSS

316LSS

316LSS

57

316SS/PEEK

316SS

316SS

28

STELLITE

316LSS

316LSS

 

 

 

 

 

29

STELLITE

STELLITE

316LSS

 

 

 

30

321SS

321SS

321SS

 

 

 

 

Note:please indicate it directly in the
order for the internal part’smaterial uncovered in the table

 

POPULAR PRODUCTS

A T-type strainer is installed in steam, gas, water, and oil pipelines. Its filter basket is inserted along the pipeline axis, giving the strainer its characteristic T-shaped configuration. The medium passes through the filter screen, which traps impurities and protects downstream pumps, valves, flowmeters, and steam traps. Face-to-face dimensions comply with ANSI B16.10, flange dimensions with ASME B16.5, butt-welding ends with ASME B16.25, design and manufacturing with ASME B16.34, and pressure testing with API 598. The product range covers NPS 2–16 and Class 150–600, with body materials including WCB, CF8, CF8M, CN7M, and LCB.

Our industrial valves are designed for optimal performance and reliability across a wide range of applications.

Globe valves pose the highest risk of leakage among all valve types: the valve stem performs linear reciprocating motion, causing friction against the packing with every opening, closing, and throttling adjustment. Furthermore, since they are often left in a partially open position for extended periods—resulting in uneven local pressure on the packing—the probability of micro-leakage is significantly higher than that of gate valves. This series is manufactured in accordance with BS 1873 and type-tested per ISO 15848-1, covering NPS ½″–24″ and Class 150–1500. Each valve is pressure-tested in accordance with API 598.

Bronze gate valves provide fully open or fully closed isolation for seawater, desalination, cooling water, and other compatible corrosive media. The range shown on this page covers NPS 2″–24″, Class 150–900, with copper alloy material options including C95800, C95500, C95600, C95200, and C95300. Face-to-face dimensions follow ANSI B16.10, flanges follow ANSI B16.5, and pressure testing follows API 598. Specify the bronze material standard and its pressure-temperature rating separately; API 600 is a cast steel gate valve standard and does not itself establish bronze material compliance.

POPULAR PRODUCTS

Seraphinite AcceleratorOptimized by Seraphinite Accelerator
Turns on site high speed to be attractive for people and search engines.